156-00302 W Brida con espárrago de fijación

The YOCL ELECTRIC 156-00302 weld stud fixing cable tie secures automotive wire harnesses and cable bundles directly to an existing stud or compatible bolt.

Fits Ø5.0 mm weld studs or compatible 5 mm ISO bolts; minimum stud length 14.2 mm.
Outside-serrated 200 × 4.6 × 1.3 mm tie; bundle range 1.5–45.0 mm.
Minimum cable tie tensile strength: 225 N.
Negro PA66HS tie / POM fixing base; operating temperature −40°C to +85°C.
Tool-free push-on mounting, lateral positioning tolerance and a movable tie head.

Consultar sobre este producto

Descripción general

The YOCL ELECTRIC 156-00302 Weld Stud Fixing Cable Tie is a pre-assembled, two-piece fixing for mounting automotive wire harnesses and cable bundles onto Ø5.0 mm weld studs or compatible 5 mm ISO bolts. Its push-on base requires a minimum stud length of 14.2 mm and installs without a dedicated mounting tool.

The fixing base allows lateral positioning tolerance at the mounting point, while the movable cable tie head can be rotated to suit the routing direction. The outside-serrated cable tie accommodates 1.5–45.0 mm bundle diameters and has a minimum tensile strength of 225 N. The tie is made from PA66HS, and the fixing base from POM.

Características

Direct stud mounting: attaches to an existing compatible 5 mm stud or bolt without a separate panel mounting hole.
Lateral positioning tolerance: helps accommodate minor differences between the fixing point and harness routing path.
Movable tie head: can be rotated into the required installation position.
Outside serrations: leave a smoother inner strap surface in contact with the cable bundle.
Construcción preensamblada de dos piezas: combines a heat-stabilized PA66 tie with a POM stud-fixing base.
Non-releasable plastic-pawl closure: retains the tie around the bundle.

Especificaciones técnicas

Parámetro	Especificación
Marca	YOCL ELÉCTRICO
Número de pieza	156-00302
Tipo de producto	Weld stud fixing cable tie
Construcción	Pre-assembled, two-piece assembly
Método de fijación	Push-on weld stud fixing
Compatible fixing	Ø5.0 mm weld stud or compatible 5 mm ISO bolt
Minimum stud length	14.2 mm
Bundle diameter	1.5–45.0 mm
Minimum cable tie tensile strength	225 N
Cable tie material	PA66HS — Polyamide 6.6, heat stabilized
Fixing base material	POM — Polyacetal
Color	Negro
Serration	Outside serrated
Closure	Plastic pawl
Releasable	No
Temperatura de funcionamiento	−40°C to +85°C
Flammability classification	UL 94 HB
Instalación	Tool-free push-on mounting

Dimensión

Dimensión	Value
Cable tie length (L)	200 mm
Cable tie width (W)	4.6 mm
Cable tie thickness (T)	1.3 mm
Fixing base length (L2)	20.0 mm
Fixing base width (W2)	21.8 mm
Height (H2)	10.0 mm
Stud diameter	5.0 mm
Minimum stud length	14.2 mm
Bundle diameter range	1.5–45.0 mm

Notas de instalación

Select a compatible Ø5.0 mm weld stud or 5 mm ISO bolt with a stud length of at least 14.2 mm.
Align the fixing base with the stud and push it into position until seated.
Wrap the cable tie around the bundle, insert the strap through the locking head and tighten it.
Position the movable cable tie head to suit the required harness routing direction.

The 225 N specification refers to minimum cable tie tensile strength, rather than stud-fixing pull-off load or installation tension.

Aplicaciones

Automotive wiring harnesses and vehicle body wiring.
Cable mounting on existing weld studs.
Vehicle interior electrical assemblies.
Wire harness assembly for commercial vehicles and transportation equipment.
Cable routing in industrial machinery and electrical equipment with compatible studs.

Información de pedido

Specify 156-00302, the required quantity, the fixing diameter and stud length, and the bundle diameter when requesting a quotation. This model has a black PA66HS cable tie and POM fixing base, a 200 mm tie length, and a 1.5–45.0 mm bundle range.