3:1 Zero-Halogen Single-Wall Heat Shrink Tubing
YOCL Electric 3:1 Zero-Halogen Single-Wall Heat Shrink Tubing provides electrical insulation, cable protection and component covering.
- Irradiated cross-linked modified polyolefin with a zero-halogen, low-smoke formulation.
- 3:1 shrink ratio for recovery around cables and components.
- Thin single wall with no internal adhesive layer.
- Fourteen sizes from 1.5/0.5 mm to 39/13 mm.
- Operating temperature up to 125°C; 300 V and 600 V rated options.
Tinjauan
YOCL Listrik 3:1 Zero-Halogen Single-Wall Heat Shrink Tubing provides electrical insulation, cable protection, wire-harness bundling and component covering. It is manufactured from irradiated cross-linked modified polyolefin with zero-halogen and low-smoke characteristics.
The 3:1 shrink ratio allows the tubing to pass over a connector or terminal and recover around a smaller cable diameter. The thin single wall has no internal adhesive layer. Fourteen sizes are available from 1.5/0.5 mm to 39/13 mm, with an operating temperature up to 125°C.
Fitur
- 3:1 recovery range: Helps accommodate connectors, terminals and components during installation.
- Zero-halogen formulation: Provides a material option for applications with halogen-content requirements.
- Low-smoke characteristics: Supports material selection for electrical and electronic equipment.
- Thin single wall: Provides a compact, flexible insulating cover.
- Modified polyolefin construction: Uses irradiation cross-linking.
- Electrical and mechanical properties: Rated voltage options, insulation test values and mechanical properties are listed below.
Spesifikasi Teknis
| Parameter | Spesifikasi |
|---|---|
| Brand | YOCL Listrik |
| Product type | Zero-halogen single-wall heat shrink tubing |
| Bahan | Irradiated cross-linked modified polyolefin |
| Konstruksi | Single wall / thin wall |
| Internal adhesive layer | None |
| Shrink ratio | 3:1 |
| Suhu operasi | Up to 125°C |
| Rated voltage options | 300 V / 600 V |
| Longitudinal shrinkage | -5% to +5% |
| Tensile strength | ≥10.4 MPa |
| Elongation at break | ≥200% |
| Tensile strength after heat aging | ≥7.3 MPa |
| Elongation after heat aging | ≥100% |
| Volume resistivity | ≥1.0 × 10¹² Ω·cm |
| Dielectric test | 2500 V for 60 seconds; no breakdown |
| Concentricity | ≥70% |
| Heat-shock test condition | 250°C ±3°C for 4 hours |
| Heat-shock test result | No dripping, cracking or flowing |
| Flammability specification* | UL224 VW-1 |
| Halogen content | Zero halogen |
| Smoke characteristics | Low smoke |
| Environmental compliance* | RoHS / REACH |
| Number of listed sizes | 14 |
*UL224 VW-1 flame performance and RoHS / REACH conformity are subject to the applicable documentation for the specific material supplied.
The 250°C condition is a heat-shock test condition. The stated operating temperature limit is 125°C.
Dimensi
| Size (mm) | Min. I.D. as supplied (mm) | Wall as supplied (mm) | Max. I.D. after recovery (mm) | Wall after recovery (mm) |
|---|---|---|---|---|
| 1.5/0.5 | 1.5 | 0.18 | 0.5 | 0.40 ± 0.10 |
| 2.4/0.8 | 2.4 | 0.20 | 0.8 | 0.48 ± 0.06 |
| 3.0/1.0 | 3.0 | 0.20 | 1.0 | 0.55 ± 0.12 |
| 4.5/1.5 | 4.5 | 0.20 | 1.5 | 0.55 ± 0.12 |
| 6.0/2.0 | 6.0 | 0.22 | 2.0 | 0.60 ± 0.12 |
| 9.0/3.0 | 9.0 | 0.25 | 3.0 | 0.70 ± 0.15 |
| 12.0/4.0 | 12.0 | 0.25 | 4.0 | 0.70 ± 0.15 |
| 15.0/5.0 | 15.0 | 0.25 | 5.0 | 0.70 ± 0.15 |
| 18.0/6.0 | 18.0 | 0.30 | 6.0 | 0.80 ± 0.15 |
| 20.0/6.7 | 20.0 | 0.30 | 6.7 | 0.80 ± 0.15 |
| 24.0/8.0 | 24.0 | 0.36 | 8.0 | 1.00 ± 0.15 |
| 30.0/10.0 | 30.0 | 0.36 | 10.0 | 1.00 ± 0.15 |
| 31.8/10.5 | 31.8 | 0.36 | 10.5 | 1.00 ± 0.15 |
| 39.0/13.0 | 39.0 | 0.45 | 13.0 | 1.25 ± 0.20 |
I.D. means internal diameter. All diameters, wall thicknesses and wall tolerances are in millimetres. Supplied dimensions and fully recovered dimensions apply to the same size row.
Panduan Pemilihan
Select a supplied internal diameter that can pass over the cable, connector or component. Check the maximum recovered internal diameter against the area to be covered, together with the recovered wall thickness.
For example, the 12.0/4.0 mm option has a minimum supplied I.D. of 12.0 mm and a maximum recovered I.D. of 4.0 mm. Its recovered wall thickness is 0.70 ± 0.15 mm.
Specify the required 300 V or 600 V rated option with the selected tubing size. Use the dimensions in the table to assess fit and the available installation space.
Aplikasi
- Automotive wire harnesses and appliance wiring.
- Electrical and electronic equipment insulation.
- Wire and cable repair, joints and branches.
- Cable identification and component covering.
Installation Notes
- Select a tubing size that can pass over the cable, terminal or component.
- Cut it to the required length and slide it into position.
- Apply controlled heat evenly around the tubing.
- Move the heat source continuously to promote uniform recovery.
- Continue heating until the tubing has recovered around the component.
- Allow it to cool before handling.
Avoid overheating or concentrating heat at one location.
Informasi Pemesanan
Specify 3:1 Zero-Halogen Single-Wall Heat Shrink Tubing, the paired size, required voltage option and quantity when making an enquiry to YOCL Electric. Include any UL224 VW-1, RoHS or REACH documentation requirements for the material to be supplied.